I’ve been looking for ages for a bathtub table. Checking Etsy first of all, looking in local shops, browsing the Internet.. Nothing suited my minimalist home the way I’d pictured it in my head (besides the prices on shipping are hilarious).
I have no idea why we didn’t do this before, it was so simple! Not to mention cheap!! And it fits my “home spa” like a glove..
You start by measuring how wide your bathtub is at the top. Drive over to your local hardware store and buy some materials. We used Royal-impregnated wood of brown colour. This material is water-resistant and the colouring goes through the whole board. We bought three boards measuring 11.5cm x 2.5cm (4.5″ x 1″).
Here our dog Nano is checking out the underside of the table. Use small boards and galvanized screws to hold the big boards together.
This is the coloring of these boards after you cut them. Royal-impregnated wood is both sturdy and nice to look at. 🙂
Here is a view from under the table. Before you fasten the screws, line everything up and be sure that the small boards on the underside line up with the edges of the bathtub!
See, now I can watch my favorite show from a tub full of suds! Go for it! 🙂
We decided to do an ice candle project before having visitors the other day! Makes for a magical atmosphere around the entrance, and feels welcoming for those dropping by. 🙂
We have made ice candles in buckets earlier, but for that you need the outdoors to be chilly enough to freeze that amount of water. Lately we have had very mild weather, so we had to turn to our freezer for help. 😛
Fill balloons with water, tie a knot to close them and put them in the freezer.
Check them every now and then, you don’t want the water to freeze all the way through!! The balloon should feel hard, with sturdy ice, but shake it to check that there is still water in the middle. 🙂
Open the balloon (cut it with a sharp knife over the sink) and pop the icy ball out.
Find the thinnest point and let the water out. Make the hole large enough for a tea light. Usually the flat part at the bottom will be rather thick, and the opposite side thinner.
If you like, you can smooth out the opening at the top by letting warm water run in the sink. Carefully rub the top of your ice light against the bottom of the warm sink until it’s melted to a nice shape. 🙂
Moving in to a new house means a lot of empty walls.. Our old pictures just don’t do the trick here. 😉 I saw a painting on one of our trips to Poland, and decided to try to make my own (as we are on a bit of a budget). A cheap canvas from Panduro, a variety of acrylic colours (Pebeo Acryllic Medium & Panduro Acryllics Matt), and paintbrushes (mostly from IKEA) do the job well enough!
After many hours of work, the completed picture lights up the wall:
Buying a professional media-bench (Unnu, Clic, Plateau etc.) for housing your speakers and stereo-equipment can be quite expensive. Luckily, you can get almost the same result by buying the right stuff from your nearest IKEA-store! You will also have to invest a couple of hours of work-time.
For the bench pictured below, you will need the following equipment:
2 * Bestå black/brown, size 120x40x38 cm (2 * £25)
4 * Lappviken black/brown, size (4 * £20)
4 * Bestå Soft closing/push-open hinge (4 * £10)
About 3 meters of speaker fabric
So the main parts cost just £170 at IKEA.
Assemble the shelving frames following the instructions. The back-plates can be omitted. Having open backs makes it much easier to run wires between the various components. Visually they aren’t really needed, since the doors/fabric will cover the front completely.
Cut out suitable holes in all the doors. This is for letting sound and infrared remote-signals through. Wrap tightly with speaker fabric, and stable on the rear side. Fit the doors to the frames as instructed.
This system will easily fit your amplifier/receiver and large front- and center-speakers. Adjust the height of the speakers with books and similar to align them with the cut-outs in the doors.
An extra bonus is that the infra-red light from most remote controls will pass through the speaker-fabric, so you can still control your amp from the remote!
Blocks of ice are always fun, especially for the kids! 😉 Add some paint and salt and watch it melt into fun shapes.
Mix your paint with a good dollop of salt, and paint it on. Add more salt if it’s taking too long! While you are painting, you might hear the crackling sound of the melting ice – it’s a nice effect and the kids really liked that part! Having fun while learning a thing or two. 😉
The finished blocks make cool props for pictures too! 😀
A few years back, I noticed our neighbor still had apples on his tree.. This was in Febuary. There was snow on the ground, and not a single leaf on the branches. It was really cool! There where no apples in my yard, so I had to make my own 😉
We have had really mild weather this January! The sun has been out for the most part, and I like it a lot! Hoping it won’t make the coming summer any colder -we need all the heat we can get in the north. Enjoying the last few hours of weekend before the workweek begins all over again ☺️